To find out how out of alignment the laser is:
• Turn off Laser.
• Hold the start/stop button and pause button and turn on the machine.
Hold it for 10 seconds then release.
• On your display it should read, “To start hardware test, use Function key.”
• Push the Function key.
• On the display it should say Check X Axis Sensor; press your Right arrow key until you get to the
menu option that says Check Laser Source.
• Once there you will hit the Enter key.
• You will adjust your power level from 50% to 10% with the down arrow.
• Once at 10% power, you move the head of your laser to the bottom right hand corner of the table.
This puts the head at the furthest point, when it gets aligned here it will be aligned for the whole
table.
• Place a strip of masking tape over the hole on the left hand side of the head where the laser beam and
red beam pass though. This will allow you to see the red beam on the masking tape.
• Then we need to close the lid of your laser.
• Push the Enter button to fire the laser until you see the masking being marked by the laser. Usually
you will see smoke - when you do, stop pushing the Enter button.
• Raise the lid of your laser. You will see where your red beam is and there will be a burnt spot
showing you where the laser is hitting.
To align the laser:
• Once you can see the red beam and the burn spot, we need to line them up together. To do this you
will need to adjust your Red Beam mirror.
• The Red Beam mirror is the square mirror located to the left of mirror #1 down by the laser tube.
• There are 5 screws located on the back of the red beam mirror. The allen head screw is NOT to be
touched at all. You will use the 90° ratcheting screwdriver to make the adjustments to the flat
tipped screws. If you are using a regular flat tipped screwdriver, you will have a lot of difficulty
getting in there and adjusting the screws.
• It really helps if you have another person there who can tell you if you are getting closer or not. Supported by: Jorlink USA, Inc. | Greensboro-NC USATel: (336) 288-1613 | support@jorlink.com | http://www.JORLINK.com
• You will adjust one screw at a time, about 1/8th of a turn. Start turning it 1/8 of a turn clockwise.
Then ask the other person if you are getting the red beam closer to the burn mark or not. If it is, do
another 1/8 turn clockwise. If not, go 1/8 of a turn counter-clockwise and then another 1/8 of a turn
counter-clockwise. See if that helps, if it doesn’t, move it back 1/8 of a turn clockwise. Then
adjust one of the other screws.
• Follow this procedure for each of the screws until the red beam is in the center of the burn mark.
• Now that the red beam and the laser are aligned together at the head, if we adjust any of the mirrors it
will move both the laser and the red beam together.
We will now need to adjust Mirror #3 one on the left hand side of the rail.
• To access this, you will lift the top of your machine.
• There will be 8 screws located on the INSIDE of your machine – 2 on the back of the machine, 2 on
the right side, 2 on the left side and 2 on the front wall.
• You will move the top of the laser over so you can access mirror #3. It is on the left side of the rail.
• Adjust mirror #3 like you did the red beam mirror. There will be 2 allen head screws you will NOT
mess with. There will be 3 flat tipped screws – adjust those.
• When you adjust this mirror, it will move both the red beam and the laser at the same time.
• Put a new piece of masking tape over the hole on the left hand side of the laser head. Adjust
mirror #3 until the red beam is right in the center of the hole on the left side of the head. The more
centered it is the more aligned it is.
• Once it is adjusted, put the top back on the machine.
• Shut the lid.
• Fire the laser again, by pushing the enter key until the tape burns and smokes.
• Make sure the red beam and the laser are in the same place right in the center of that whole. If they
are not together and right in the center of the hole, follow the procedure again.
• Once the red beam and the burn mark are in the center of the hole on the left hand side of the head of
the laser it will be aligned.
• You can redo the 4 Square cut test. The squares should cut evenly. If it doesn’t follow major
beam alignment section after this one.
MAJOR BEAM ALIGNMENT
1. Turn off the laser.
2. Remove the side cover and prism mount for mirror 1.
3. Put a piece of target paper 3 M away from the machine.
4. Hold Start/Stop and Pause button. Turn on the laser. Use your right arrow to select “check laser source”
in the Diagnostic Process. Set the power to 10% on 25W machine, (adjust accordingly for you particular
wattage of machine).
5. Press Enter till the target has a small burnt spot on it.
6. Adjust red beam mirror or red beam diode until red beam and burn spot are in same spot.
7. When this process is finished please re-assembly the cover over mirror 1
Schreib mir mal eine private Nachricht bidde 
