γεια σας ειμαι νεος με το σπορ και εχω προβλημα με το λειζερ μου δεν κοβει τιποτα .. αλλα γκραβουρες κανει πολλυ καλα θα ελεγα
μπορω να εχω μια βοηθεια σασ παρακαλω
γεια σας ειμαι νεος με το σπορ και εχω προβλημα με το λειζερ μου δεν κοβει τιποτα .. αλλα γκραβουρες κανει πολλυ καλα θα ελεγα
μπορω να εχω μια βοηθεια σασ παρακαλω
Äh, ja....
... Για την κοπή, θα χρειαστείτε πιθανώς περισσότερη δύναμη ή να το χαράξετε αρκετές φορές μέχρι να γίνει
γεια σας ειμαι νεος με το σπορ και εχω προβλημα με το λειζερ μου δεν κοβει τιποτα .. αλλα γκραβουρες κανει πολλυ καλα θα ελεγα
μπορω να εχω μια βοηθεια σασ παρακαλω
ZitatHallo, ich bin neu in diesem Sport und habe ein Problem mit meinem Laser, er schneidet nichts. Aber beim Gravieren funktioniert er sehr gut. Ich würde sagen, kann ich bitte etwas Hilfe haben?
ΜΠΟΡΩ να εχω βοηθεια
... αν περιγράψετε σωστά το πρόβλημά σας και μας πείτε επίσης τι είδους συσκευή λέιζερ έχετε, ίσως.
Θα βοηθούσε επίσης αν χρησιμοποιούσατε ένα μεταφραστικό πρόγραμμα, όπως το DeepL, έτσι ώστε να μην χρειάζεται να μεταφράζουμε τα
Mit meinem Handy funktioniert die Übersetzung nicht.....
... sein Laser graviert gut, schneidet aber nicht
Ich habe ihm gesagt, daß er doch bitte sein Grät vorstellen sollte und ggf. schon vorher mal mit DeepL übersetzen, damit das auch so zu lesen wäre
Mit meinem Handy funktioniert die Übersetzung nicht.....
google translate odee besser Deepl.
Γεια σας, έχω δύο δέντρα 55 pro τώρα το αγόρασα και έχω πρόβλημα με το λέιζερ που δεν κόβει καθόλου. Graves κάνει καλά 2000 ταχύτητα 60 δύναμη.
Το έβαλα να κόψει 10 ταχύτητα 100 δύναμη 5 πέρασμα 3mm mdf
Και το αποτέλεσμα είναι σχεδόν σαν χαρακτική. Κόβει ελάχιστα.
Hello I have two trees 55 pro now I bought it and I have a problem with the laser not cutting at all. Graves does well 2000 speed 60 power.
I put it to cut 10 speed 100 power 5 pass 3mm mdf
And the result is almost like an engraving. It cuts very little.
Do you use Lightburn?
If so, check the max-s value in machine settings if it is set to 1000.
Otherwise the Laser only runs at 1/4 of its power.
s value max 1000 i have
is there a chance that the laser is broken and can make good engravings and not cut???
$0=10
$1=25
$2=0
$3=5
$4=0
$5=0
$6=0
$10=1
$11=0.010
$12=0.002
$13=0
$20=0
$21=0
$22=0
$23=5
$24=300.000
$25=1000.000
$26=250.000
$27=1.000
$28=1000.000
$30=1000.000
$31=0.000
$32=1
$41=1
$47=1
$46=1
$102=100
$101=80
$45=0
$44=1
$43=1
$42=1
$50=2
$40=1
$100=80.000
$103=100.000
$104=100.000
$105=100.000
$110=10000.000
$111=10000.000
$112=6000.000
$113=1000.000
$114=1000.000
$115=1000.000
$120=2500.000
$121=2500.000
$122=500.000
$123=200.000
$124=200.000
$125=200.000
$130=301.000
$131=301.000
$132=50.000
$133=300.000
$134=300.000
$135=300.000
ok
Its ok ??
Für Euch nur mal so, was ist das für eine Einstellung?
Ist das ein ESP32 Pro Ver als Controller?
Ich mach mir jetzt nicht die Mühe es zu übersetzen....aber das GRBL schaut nett aus : )
Na schau an...es ist wohl ein ESP 32 Pro und da sollte man eventuell mal ein Update machen?
Kein Plan welche Version da jetzt drauf installiert ist.
Ich bin der Meinung V 4.1 sollte es sein.
$120=2500.000
$121=2500.000
These Values are extremely Hig for a Diode Laser.
Maybe try 300 to 500 for start.
3mm MDF is also not the easiest to cut, because of the high amount of Glue in it.
Also aheck if the focus is correctly set.
V4.00(8M.H35.20230918)]
[VER:1.1h.2023091801:]
[OPT:VMPH,63,256]
Target buffer size found
[MSG:Using machine:MKS DLC32]
I don't know what else to do, I think I've got it all... unless the laser has a problem when it goes off.
Thanks a lot for helping me.